Please read all instructions before using your Vapor Slide.
Insert small end of micro-USB charging cable into the micro-USB port. Plug large end of the charging cable into any USB 2.0 outlet for example on your computer or using your phone USB wall adapter. A red light will turn on just above the micro-USB port to indicate that it is charging and will turn green when fully charged.
Choose the appropriate tank size (small 9mm tank or larg 14mm tank) for your water pipe or hookah. To open smaller 9mm tank, simply pull on the black mouth-tip. For the larger 14mm tank, unscrew the black mouth-tip counter-clockwise. Once opened, use a dropper/pipet, plastic squeeze-bottle with a small tip, or a blunted syringe to fill the tank with e-liquid. Be careful to avoid the center hole. When the e-liquid level has reached the top of the center post where the wicks are attached, reattach the black mouth-tip.
IMPORTANT: When flling a brand new, dry tank, DO NOT immediately screw the tank onto the Vapor Slide. With a fresh, dry wick you must inhale on the mouth tip several times and then let the tank sit for 5 minutes to allow the e-liquid to fully saturate the wick before use. Failure to properly saturate the wick will result in an undesirable burning taste caused by charring the wick.
Screw the bottom of the tank into the bottom of the Vapor Slide. Screw the tank until you feel it stop turning with slight resistance.
IMPORTANT: Do not over-tighten the tank. As soon as the tank stops freely spinning it has made ideal connection to the battery. Excessive over-tightening will result in stripping the threads and/or breaking the thead-connection on the Vapor Slide.
Slide the tank attached to the Vapor Slide into the down-stem of the water pipe. Be sure that the water does not touch the black mouth-tip.
IMPORTANT: If the e-liquid tank becomes submerged underwater, or excessive water splashes into the coil of the tank, an undesirable burning taste could result and possibly ruin your tanks.
Before using the Vapor Slide for the first time (or using a new tank or new e-liquid) turn the voltage knob on top counter-clockwise until the red line on the knob lines up with 3.3V. Increasing the voltage will increase the amount of power going to the coil inide the tank which will produce more vapor.
IMPORTANT: You should always start at the lowest voltage setting when using a new tank or a new e-liquid to avoid burning the coil prematurely.
With the tank properly filled and slide inserted into the water pipe, simply inhale as you normally would through the water pipe. The Vapor Slide will activate automatically causing the LEDs on top to glow indicating that your e-liquid is vaporizing. When the water pipe has filled with vapor slightly pull the slide out and inhale. If you desire more vapor, turn the voltage knob clockwise to the next higher voltage marking.
IMPORTANT: Although the Vapor Slide can reach a maximum voltage of 4.8 volts, not every e-liquid or tank can handle this much heat. Start at the lowest voltage setting, test it, then increase by one voltage setting at a time to avoid a burning taste. If at any point the vapor tastes burnt, decrease the voltage setting. However, every e-liquid tank will eventually burn out. If your vapor begins to consistently taste burnt regardless of the voltage seting, it is time to replace your tank.
IMPORTANT: Do not submerge the Vapor Slide in water at any time.
Cleaning: After a day's usage of the Vapor Slide, remove the tank and use a dry paper towel or cotton swab to clean the 510-threading on the bottom cone of the Vapor Slide. If excessive residue has built up on the metal connection, slightly wet your paper towel or cotton swab with rubbing alcohol and wipe the metal connection while holding the Vapor Slide in it's upright position so as not to let the rubbing alcohol drip inside.
Storage: To avoid accidental structural damage to your vaporizer, store your Vapor Slide in the included zipper case. Do not leave a tank attached to your Vapor Slide while stored in it's case. Be careful to securely tighten any bottles of e-liquid that you may store with or near your Vapor Slide, as liquid from a leaky or broken bottle may damage the electronic components of the Vapor Slide.
Tanks of e-liquid should not be stored in excessively hot or cold environments. Excessive heat, such as in a hot car during the Summer time, could cause the coils in the tank to rapidly expand, allowing an unwanted amount of fluid to flood into the mouthpiece. Extreme cold can cause the e-liquid to thicken, which will inhibit it's ability to wick fast enough and thus burn your wick.
Do not leave your Vapor Slide kit in excessively humid environments, as too much moisture can damage the electronic components of the Vapor Slide.
Any tank used for vaporizing on any device, including the Vapor Slide, will eventually expire with use. The vapor production will decrease, and the flavor will become undesirable. When this happens, it is time to replace your tank.